Product details

Contral device: built in controlier Product structure: no power off, gude rail type, high curert, smal volume, two-stage type, simple structure,
ATS integretior Features: fast switching speed, low failure rate, convenient maintenance and reliable performance
Wnng mode: front plate wiring
Conversion mode, power grid to powwer grid, power grid to generator, automstic switchingandsrcovr
Product frame: 100 Product current: 10,16, 20,25, 32,40,50, 63, 80, 100A
Product dassifcation direct load type Pole No: 2.3.4
Standard Ge/T14049 11 ATSE PC class
Switching time: 0 008s.8ms

Summary
The dual power automatic swtch is a newly developed minianure household power swtch, which s manly used the standby power supply starts to work immediately, which ensures the continuity, reliatity and safety of power 400V AC ATS has the characteristics of solid structure, reliable conversion, conven ent installation and mainterance operated by electricity or manualy ATS composed of TSE and controller. that ATS is the most quaifed low-voltage swtchgear and control device

Normal operation time and installation conditions
Ambient airtemperature
The maamum temperature shal not exceed 40C the minimum temperature shall not be lower than -5'C. and the average temperature wthin 24 hours shal not be higher than 35C
Althude The atitade of the nstalation site should not be higher than 2000m
Atmospheric conditions When the maximum temperature reaches 40C, the relatve humidty of the installaton site should not exceed 60%, when the terperature is the mnum terperature-5C, the relative humdity is higher, for example, the tern -perature is 25C, and the relative humidty s 90%
Due to the terrperature change, spedal measures should be taken to deal with the oocasienal condensation en the surface of the product. Pallubon grade
The poluton grade of ATS conforms to grade 3 spechied in GB/T14048 11 Indlaton category
The installation type of ATS corfoms to the category specfied in OB/T14048.11 Installation comdbans ATS can be nstalled verticaly in control cabinet or distributon cabinet.
Make sure the instalaton cistance meets the requirements in Figure 1

Installation and wiring
Ensura that eofassionas a af this maual hafora inctallahon and wionl 9 Please chedk the inteanty cf ATS hefnee inetalabon then onen and dose ATS wth the cneratinahandle hen he fextilty of transmsson device and detect the load generation and dsoonnecton conditons of common and standby Dower supnles a each stage 2 Sas ta haues tee tha caract ieetslaton etane Tha tesdamack ie in teast at ta smd iet itha ieetailshan csnnsk be camied out according to the correct procedures due to wiring and other reasons, please contact us. The safs dstances S1. S should ngt be lgrer than the labels Fia.e iSee haure telawfor detais) 4 Detection control voltage SCHz, AC220V The col in the control dircuit cannot be too long, The cross-sectional area of copper wire shouid not be greater than 2 0mm 5 According to the installaton requirernerts of povver distrbution system, please provide appropriate crcuit breakers to ensure the safety of sta and equipment.

Maintenance, inspection and storage
M antenance and inspecon shal be operated by professionas and al power supples shalbe out off in advance 2. In order to ensure the good perfommance of ATS, the first marenance and inspecton shal be carned out withnl 6 morts after use and shall be mantained and rspected at least once a year In harsh installation candtons. the frequency of maintenance and inspection should be increased. 3. Maintenance and inspection ibers b. Please check whether the contact parts of the electrical contacts are deformed and damaged and remove burnt c Rust acidification and dust on the contact surface may lead to poor contact Please operate menualy many times d. Due to long-tem moisture and suspension, please dry ATS before use After rermoving dust and drt, use a S00v megommeterto measure the sulaon restance beteen namal supply atemang pawer supoyoad sde bar induding ive parts and metal plate. And the insulation resstance should not be less than 10M Ω 4. ATS shall be stored in an environment equvalent to the nomal wong enronmert th duspraot moture proof and collision-proof measures.